LGK Series of Digital Plasma Cutting Machine
Features:
■ Pre-gas sending can effectively protect the nozzles and electrodes
■ Current up slope, can reduce the consumption of nozzles and electrode and reduce the spatter
■ Cutting current and time can be preset
■ Support 2T/4T, easy to operate, with robot interface and manipulator interface
■ With arc start signal, easy to control with robot and manipulator
■ Post gas sending time adjustable, which can effectively protect the nozzles and electrodes
■ HF small-current arc ignition controllable, high success rate, lower nozzle and electrode consumption
■ Parameters can be saved automatically while machine is powered off
■ Stable welding can be realized over classified optimization, absorption, shielding and venting of HF interference signals
■ Can cut mild steel, stainless steel, alloy steel, aluminum and its alloy, etc.
■ Defaults all-progress monitoring, effectively guarantee the operation of equipment
■ With torch default auto checking function for short circuit (error code E00), overheat checking (error code E02)
■ Input power default auto checking (error code E01), air pressure auto checking, auto protection without gas (error code E03), water pressure auto checking (error code E04)
RSN Series of IGBT Inverter All-digital Stud Welding Machine
Features:
■DSP digital control, with 30 saving channels
■Menu and functions LCD display, with general model and intelligent model
■Presetting of welding current and welding time, expert database usable for intelligent welding
■Arc-start program system automatic optimized, arc starts well, weld bright and beautiful
■Welding time is short, energy concentrated
■Torch with cooling unit inside, thus can reduce the power consumption and prolong the torch’s service life
■Torch with damper outside, few spatter
■The long-cycle stud welding machine is suitable for steel structure, shipyard, bridge, boilers, and on so on; the short-cycle stud welding machine is suitable for chassis, sheet metal, furniture, machinery manufacturing, boiler, etc.
■The long-cycle stud welding machine RSN-1600/2000/2500/3150 can also weld stud and bolt ofФ3-12mm like short-cycle stud welding
ZX7-400-B IGBT Inverter DC MMA Welding Machine (for Downward Welding of Cellulose Electrode)
Features:
■ Automatic protection from over-current, over-heat, over/under-voltage
■ Arc burns stably, molten pool good, fine welding seam
■ Suitable for many kinds of electrode (cellulose electrode, low-hydro electrode and common electrode)
■ Small and light
■ Specially suitable for tube's downward welding with cellulose electrodes like E6010, E8010, E7048
■ Suitable for welding pipelines
WSM7-D Series All-digital Pulse TIG Welder
Features:
■ Start arc with HF Pulse, adopt DSP digital control, with 30 saving channels
■ Automatic protection from overcurrent, overheat, over/under voltage
■ Support DC TIG welding, pulse TIG welding and MMA welding, can weld such metals as stainless steel, alloy steel, copper, silver, titanium, etc.
■ LCD shows menu and functions, with fast forward key on the front panel
■ Pre digital set of welding current, current up/down slope
■ Arc burns stably even the lowest output current is 10A, even 5A
Discover the Power of Our Custom-Made Stud Welders!
- Features
■ Automatic protection from overcurrent, overheat, over/under voltage, and phase lacking
■ Strong penetration capability of arc and deeper fusion penetration
■ Support stud welding and manual welding
■ Easy to strike arc, fine welding seam
■ Support continuous adjustment of welding current and welding time
Robot Narrow Gap Hot Wire Argon Arc Welding
In recent years, with the development of welding industry and continuous improvement of welding technology, narrow-gap auto welding is attracting more and more attention. At present, the narrow auto welding system mainly adopt SAW welding and tungsten-rod TIG welding.
The advantages of narrow gap automatic welding are: reducing the amount of metal filling, saving a lot of welding materials and welding time, thereby greatly reducing the welding cost of the weld seam; The low heat input of the weld seam refines the microstructure of the welded metal and heat affected zone, improving the mechanical properties of the weld seam.
The narrow gap automatic welding system we produce consists of heavy-duty robots, wire feeding mechanisms, narrow gap welding guns (including swinging devices), welding equipment, etc.
The narrow gap automatic welding system is mainly applied in industries such as nuclear power, chemical equipment, pressure vessels, wind power, ships, bridges, petroleum, mining machines, etc.
The narrow gap automatic welding systems we exhibited at this Essen exhibition are mainly three types of robot narrow gap automatic welding systems, which are introduced as follows:
The robot narrow gap hot wire argon arc welding is composed of a heavy-duty welding robot, a hot wire argon arc welding machine, and a narrow gap welding gun.
Heavy duty welding robot, model: SYB1830B
Robot features: low noise, good linearity
Modular design, high reliability
High intelligence and security
Basic Parameter |
Degree of freedom |
6 |
Installation means |
Ground/Side Wall/Inverted Hanging |
Verified load |
30kg |
Power capacity |
4.5KW |
|
Additional load of J3 axis |
25kg |
Power voltage |
3-phase 380V |
|
Robot body weight |
About 255kg |
Brake system |
All axis with brake |
|
Repetitive positioning accuracy |
±0.08mm |
|||
Action range |
Maximum reach distance of point P |
1809mm |
J3 axis (upper arm swing) |
-85°~+95° |
Minimum reach distance of point P |
491mm |
J4 axis (arm rotation) |
±360° |
|
J1 axis (turn) |
±180° |
J5 axis (wrist pitch) |
±130° |
|
J2 axis (lower arm swing) |
-170°~+90° |
J6 axis (wrist rotation) |
±360° |
|
Highest speed |
J1 axis (rotation) |
122°/s |
J4 axis (arm rotation) |
168°/s |
J2 axis (lower arm swing) |
70°/s |
J5 axis (wrist pitch) |
270°/s |
|
|
|
|
|
|
|
|
|
|
|
J3 axis (upper arm swing) |
138°/s |
J6 axis (wrist rotation) |
337°/s |
|
End synthesis speed |
1.2m/s |
|||
Allowable torque |
J4 axis 60.0N.m J5 axis 60.0N.m J6 axis 50.0N.m |
Hot wire argon arc welding machine, model: DSP-400/RS
Hot wire argon arc welding consists of a welding power source, a hot wire power source, a water cooling system, and a vibrating digital wire feeder.
Welding machine features:
- The welding machine and automatic wire feeder are both digitally controlled by DSP and communicate digitally.
- The LCD menu touch screen function display of the welding machine and automatic wire feeder.
- The wire feeder can choose from vibrating wire feeding, constant speed wire feeding, and pulsating wire feeding.
- When vibrating wire feeding, it is beneficial to stir the melt pool and make the crystal grains finer,
- Better mechanical properties of welds; Stir to remove volatile gases and bubbles from the melt pool,
- Improved welding quality; The vibration function improves the welding ability at all positions; send
- The molten droplets are easy to detach from the welding wire and enter the molten pool.
- Automatic heating of welding wire, hot wire current: 10-200A;
- The welding speed is more than twice that of a regular argon arc welding machine.
- There are 30 storage channels
Narrow gap TIG welding gun
Suitable materials: carbon steel, low-alloy steel, stainless steel, etc
Suitable for narrow groove welding of 15mm or more
During welding, the wire swinging technique ensures that both sides of the groove are fully fused together
High deposition efficiency, low heat input
It can achieve various welding positions such as horizontal welding, vertical welding, and overhead welding
Parameters
Name |
Parameter |
Maximum depth of groove |
300mm |
Groove width |
15mm以上 |
Deposition efficiency |
250g/min |
welding speed |
100-300mm/min |
welding wire |
1.2mm |
Welding gun (conduct tip) swing angle range(°) |
≤±3.5 |
Welding gun (conduct tip) deviation angle accuracy(°) |
≤±0.5 |
Welding wire swing frequency |
0-100time/min |
Left and right dwell time(S) |
0-9.9 |
Protective gas |
Ar 99.99% |
NBC-1000 gas-shielded-arc welding machine
■ Adopt the soft switch technology, high efficiency, low power consumption
■ Automatic protection from over-current, overheat, over/under voltage
■ Support digital display and presetting of current and voltage, wide adjustment range of voltage
■ Particular function of automatically removing melting-ball from the end of the welding wire
■ Adopt the closed-loop system to control arc and waveform control system to adjust the arc force
■ Suitable for low carbon steel and low alloy carbon with solid/flux-cored welding wires of different specifications
■ Widely used in such areas as automobile, shipbuilding, bridge, petrol chemistry and construction, and so on
■ Wire feeder is driven by four wheels, big power, and feeding wire stably
■ A voltage fluctuation of ±20% is allowable
■ Small size, light weight
■ Support frequent welding, little spatter, high efficiency in melting metals
- Main parameters
|
NBC-800 |
Power |
3-phase 380V/415V 50Hz |
Rated input power |
55KVA |
Rated input current |
83A |
Rated current/voltage |
1000A/44V |
Welding curr. |
80% |
Adjustment range of welding curr. |
40-1000A |
Adjustment range of welding volt. |
16-50V |
Pre-gas sending |
0-1S |
Post-gas sending |
0-4S |
Suitable wire |
1.2-2.4mm solid/flux cored wire |
No-load voltage |
90V |
Air switch |
100A |
Input cable |
4*16mm2 |
Insulation class |
F |
Protection class |
IP23 |
MZ-WH-A-SX Tandem-wire Tandem-power Tractor
MZ-WH-A-SX tandem-wire tandem power auto SAW tractor can be used with SAW welding machine of 630A, 1000A, or 1250A, even 1600A.
Usage:
This tractor is suitable for AC or DC tandem power supply, tandem wire submerged arc welding. It can support welding of one weld, or two parallel welds, or fillet welding. It is used for welding various types of medium wire feeding heads, box beams of thick steel plates, H-beams, etc. It can such materials like carbon steel, low-alloy steel, heat-resistant steel, etc.
Characteristics:
- The tractor travels stably, has a wide welding range, and is easy to adjust.
- Head rotation/horizontal angle adjustment handle (Figure 2), adjust the horizontal and vertical angles of the wire feeding head, weld flat and corner welds with different requirements, and achieve a minimum of 20mm for the front and rear welding guns. Weld one weld seam and use one machine for multiple purposes.
- Equipped with a horizontal long-distance heavy-duty straight track, can be used in stead of the traditionalgantry welding , the welding trolley has extremely strong stability.
- Angle of the flux container can be adjusted, which canto ensure smooth wire feeding after the wire feeding machine moves along the straight track.
- With two control panel install plates.
- Adopting a single wire feeding wheel to reduce the extrusion pattern of the welding wire to improve the service life of the conductive nozzle and the conductivity of the welding wire, with low mechanical loss, strong wire feeding force, and good welding stability.
Main Parameters
Item |
MZ-WH-A-SX |
MZ-WH-A-SX001 |
MZ-WH-F-SX |
Rated input voltage of marching unit |
servo motor DC110V Permanent magnet |
servo motor DC110V Permanent magnet |
servo motor DC110V Permanent magnet |
Rated input voltage of wire-feeding unit |
Servo motor DC110V permanent magnet (excitation optional) |
Servo motor DC110V permanent magnet (excitation optional) |
Servo motor DC110V permanent magnet |
Wire feeding reducer |
Worm gear reducer |
Worm gear reducer |
Spiral gear reducer |
Range of welding speed |
0.2~1.5m/min |
0.2~1.5m/min |
0.2~1.5m/min |
Range of wire-feeding speed |
0.25~3m/min |
0.25~3m/min |
0.25~3m/min |
Suitable welding current |
630A、1000A、1250A |
630A、1000A、1250A |
630A、1000A、1250A |
Suitable wire |
Ф2~Ф6.0mm |
Ф2~Ф6.0mm |
Ф2~Ф5.0mm |
Horizontal and lateral movement adjustment of columns |
65mm |
65mm |
65mm |
Torch overall deviation |
Yes |
Yes |
Yes |
Column adjustable height |
90mm |
90mm |
90mm |
Conductive nozzle lifting range |
80mm |
80mm |
120mm |
The relative adjustable distance between the two heads |
300mm~1000mm |
300mm~1400mm |
20mm~1000mm |
Horizontal movement adjustment of crossbeam |
80mm |
80mm |
80mm |
Multi-usage welding |
/ |
/ |
Flat welding double wire (2 guns can weld one weld seam) |
The angle of rotation of the crossbeam around the column |
±90° |
±90° |
±90° |
Head rotation angle |
±45° |
±45° |
±45° |
Torch moving angle |
±45° |
±45° |
±45° |
Tractor moving power |
2-wheel drive |
2-wheel drive |
4-wheel drive
|
Material blocking plate |
2set |
2 sets |
2sets |
Flux capacity |
8L×2 |
8L×2 |
8L×2 |
Wire capacity |
25Kg×2 |
25Kg×2 |
25Kg×2 |
NBC-G Deep-penetration Twin-wire MIG Welding machine
The G-type deep penetration pulse welding machine is a further electromagnetic compression arc welding machine based on high-speed pulse welding machine, which makes the arc density higher, the arc more concentrated, and the arc more straight to achieve greater penetration, which is conducive to welding medium thick plates. The welding speed is faster and the heat input is low. Especially when using double 1.6mm welding wire for high current welding, the matching power supply is larger. If using 1.6mm solid core welding wire, the welding current is 300A, and the matching voltage can be 27V, which is very suitable for metals with high heat input requirements.
Gas shielded welding with flux cored wire has been promoted and widely used in industries such as shipbuilding, steel structures, bridges, automobiles, and mining machinery for many years. The gas shielded welding of flux cored wire mainly uses pure CO2 gas or 20% CO2+80% Ar as the shielding gas, and the process is very mature. However, there are still some shortcomings in the application process, mainly including: firstly, the welding wire is prone to moisture; Secondly, when welding with 1.2mm flux cored wire at currents below 160A, there are small balls at the end of the wire, which is not conducive to controlling the arc and molten pool. Therefore, welding with currents above 160A is mostly used; Thirdly, the depth of melting is shallow, the arc is weak, and the penetration power is not strong.
When we use deep penetration high-speed pulse or high-speed pulse welding in flux cored wire, even the current is 80A, arc spray transition can also be realized. And there are no small balls at the end of wire when arc burns. The molten pool and arc are easy to control, and the molten pool is clear; The melting depth is greater, 30% greater than that of the core wire in general DC gas shielded welding. High speed pulse arc has greater stirring force and stronger arc force. Therefore, it is easier for flux cored wire welding slag and gas to overflow during welding.
Features
- Support deep-penetration welding, high-speed pulse welding, DC MAG welding
- While welding mild steel, its speed is 1-1.3 times of the general MIG/MAG welding, and its penetration force is also 45% higher than the general MIG/MAG welding
- Welding flux-cored wire, arc is is stronger, and the penetration force is 30% higher than the general MIG/MAG welding
- While using pulse welding or synergic welding, there will be few spatter
- Suitable for welding of medium/thick plate in such industries like steel structure, ship-making, bridge, windpower, and so on
Parameter
Model Contents |
NBC-630G |
NBC-800g |
Input power source |
3-phase 380V/415V 50/60Hz |
|
Rated input current |
52A |
63A |
Rated input capacity |
34KVA |
42KVA |
Rated welding curr./Volt. |
630A/44V |
800A/44V |
Duty cycle |
100% |
100% |
No-load voltage (MAX) |
80V |
90V |
Adjustment range of welding curr. |
40-630A |
40-800A |
Efficiency |
≥85% |
|
Power factor |
>0.95 |
|
Diameter of wire |
Ф0.8~Ф2.0mm solid/flux-cored wire |
|
Insulation class |
F |
|
Protection class |
IP21S |
Our NBC-630G/800G can weld two wires of 1.0mm, 1.2mm, and 1.6mm.
MZE-2500 One Power Twin-Wire SAW Machine
Machine features
- IGBT inverter full-bridge soft-switch inverter technology, higher efficiency, more energy saving
- Auto switch off from phase lack, over current, over heat, and over/under-voltage
- Welding current, voltage and marching speed can be preset accurately
- Strong ability to suppress network voltage fluctuations, with a width of up to ± 20%, duty cycle of power source is as high as 100%
- Wire feeding auto checking, wire sending stop automatically while the wire is well contact to work-pieces, and wire feeding will speed up automatically while pressing the wire back button. Wire will be sent back automatically while welding finish
- AC frequency and duty cycle both adjustable
- Two wires will not influence each other and will not interfere each other
Technical features
- In AC SAW welding, the heat input is lower than that of DC SAW welding, suitable for welding metals such as high-strength steel, ultra-high strength steel, and nickel steel
- AC SAW welding is suitable for splicing welding, welding with small deformation, welding with few heat affected zones
- Can realize three-wire or four-wire welding together with DC SAW welding machine and realize quick and high efficiency welding
Technical Parameters
Model Name |
MZE-2500 |
Input power |
3-pahse 380V or 415V 50Hz |
Rated input power |
147KVA |
Rated input current |
223A |
Welding current |
2500A 100% |
No-load voltage |
90V |
Welding current |
200-2500A |
Diameter of wire |
Φ3-6mm*2 |
AC frequency |
5~60Hz |
Duty cycle |
0~100% |
Air switch |
250A |
Input cable |
4×25mm2 |
Insulation grade |
F |
Lift means |
Lift |
Protection grade |
IP21S |
NBC-800SS Deep Penetration Gas-shieded-arc Welder
The G-type deep penetration pulse welding machine is a further electromagnetic compression arc welding machine based on high-speed pulse welding machine. When the arc is compressed, the arc density is higher, the arc is more concentrated, and the arc is more straight to achieve greater penetration, which is conducive to welding medium thick plates. The welding speed is faster and the heat input is low. Especially when using 1.6mm or more welding wire for high current welding, the matching power supply is larger. If using 1.6mm solid core welding wire, the welding current is 300A, and the matching voltage can be 28V, which is very useful for metals with high heat input requirements.
The model we developed using deep penetration pulse welding: NBC-800SS welding machine (deep penetration pulse single arc double wire welding machine), can match low voltage welding with double 1.0, double 1.2, and double 1.6 welding wires.
Welding machine features:
① It has functions of deep penetration pulse welding, high-speed pulse welding, and DC gas shielded welding
② The solid wire with a diameter of 1.2 can be stably welded with a small current of 40A; Low current welding can replace TIG welding, with a speed 4-5 times faster than TIG welding.
③ When welding with functions such as pulse and unification, ultra-low spatter can be selected.
④ When welding carbon steel, the welding speed is 15% faster than ordinary gas shielded welding, and the penetration force is 60% greater.
MCT-350 Cold-arc Welder
Cold arc welding, also known as cold metal transition welding, currently mainly includes STT (surface tension transfer), CMT (timely wire withdrawal), and Cold Arc (timely shutdown at the moment of arc short circuit) to achieve cold arc.
Sichuan Morrow Welding Development Co., Ltd. has developed cold arc transition welding machines such as DSP-500TG5 cold arc welding function 10 years ago. In 2023, we developed a timely withdrawal welding wire to achieve cold metal transition welding machine. Our welding machine model is MCT-350, which is matched with robots for high-quality cold arc welding.
Main features:
① The welding machine adopts IGBT inverter technology and DSP digital precise control.
② It has overcurrent, undervoltage, overheating, and phase loss protection functions.
③ Wire retraction frequency: 80-120Hz.
④ During welding, the heat input to the weld seam is low.
⑤ No spatter welding, and the arc is very stable.
⑥ High quality welding of thin plates suitable for arc short-circuit transition
Welding and bridging.
⑦ Can weld carbon steel, stainless steel, aluminum and its alloys, copper
Various metals such as galvanized sheet.
MZ7-1600/MZE-2500 Three-Wire Three-arc Sumberged-Arc Welder
Features:
■ Both the power supply and welding trolley adopt DSP all-digital control and communication
■ The system has a built-in welding expert database and can also store 30 sets of custom parameters
■ Equipped with arc start anti sticking and automatic wire drawing function upon arc stop
■ Current/voltage/walking speed digital display and pre-set in advance
■ The communication frequency and duty cycle can be adjusted
■ The simultaneous operation of AC and DC power sources does not affect or interfere with each other
■ Low heat input, further improving welding efficiency
Discover the Power of Our Custom-Made Submerged Welding Machines
Are you looking for a high-quality, custom-made welder designed to meet the rigorous demands of your industry? Our Submerged Welding machines are the perfect solution for welding medium and thick plates across various applications. With the latest IGBT inverter technology, our machines offer unparalleled energy efficiency and superior performance, ensuring your welding tasks are completed with precision and ease.
Advanced IGBT Inverter Technology
One of the standout features of our Submerged Welding machines is the incorporation of cutting-edge IGBT inverter technology. This technology not only enhances the machine's performance but also contributes to significant energy savings. By reducing power consumption, our machines help lower your operational costs while being environmentally friendly.
High Automation and Efficiency
Our Submerged Welding machines boast a high degree of automation, which simplifies the welding process and reduces the need for manual intervention. This high level of automation ensures consistent weld quality, minimizes human error, and boosts productivity. Whether you're working on pipelines, steel structures, shipbuilding, automotive manufacturing, boilers, or wind power towers, our machines deliver exceptional results every time.
Exceptional Customer Experience
We prioritize customer satisfaction by providing custom-made welders tailored to your specific requirements. Our Submerged Welding machines are designed with the user in mind, offering intuitive controls and robust construction that ensure a smooth and reliable welding experience. The feedback from our customers highlights the ease of use, durability, and superior weld quality that our machines consistently deliver.
Versatile Applications
Our Submerged Welding machines are versatile and suitable for a wide range of industries. They excel in welding medium and thick plates, making them ideal for applications in:
- Pipelines: Ensuring strong and leak-proof joints for long-lasting pipeline infrastructure.
- Steel Structures: Providing robust and reliable welds for various steel construction projects.
- Shipbuilding: Meeting the stringent quality standards required in shipbuilding.
- Automotive: Delivering precision and durability for automotive manufacturing needs.
- Boilers: Ensuring high-quality welds that withstand high pressure and temperature.
- Wind Power Towers: Supporting the construction of durable and sustainable wind energy solutions.
Environmentally Friendly
In addition to performance and efficiency, our Submerged Welding machines are designed with environmental sustainability in mind. The advanced technology reduces energy consumption, contributing to a lower carbon footprint. By choosing our machines, you are not only investing in high-quality welding solutions but also supporting a greener future.
Conclusion
Investing in our custom-made Submerged Welding machines means choosing reliability, efficiency, and superior weld quality. With features like IGBT inverter technology, high automation, and excellent customer experience, our machines are the perfect choice for various industrial applications. Enhance your welding operations and experience the benefits of our state-of-the-art welding solutions today.
MZ-ZK-630 CO2 Welding Tractor
MZ-ZK-630 light Co2 tractor is the derivative product based on automatic submerged arc welding tractor while incorporating our twenty years experience in wire feeding mechanism as well as suggestions from our customers both at home and abroad.
This tractor is suitable for Panasonic type Co2/MAG welding. It can use Panasonic or Euro adaptor.
Features:
- This tractor is composed of base, traveling mechanism, frame, wire feeding bracket assembly, slide assembly, wire spool, control box and torch assembly. The torch position can be adjusted easily and accurately.
- Double driven wire feeding with straightening mechanism, stable wire feeding, good centering, strong drawing and feeding force and low power dissipation.
- This tractor works with related welding power source and suitable for Co2 gas shield welding of long weld seams.
Parameter
Items |
Specification |
Rated input voltage of traveling mechanism |
Servo motor DC110V(permanent magnet) |
Rated input current of traveling mechanism |
0.4A |
Rated input voltage of wire feeding mechanism |
Print motor DC18.3V DC24V |
Rated input current of wire feeding mechanism |
5A/5.5A |
Type of wire feeding |
Continuous wire feeding |
Welding speed |
0.2~2.2m/min 0.4~2.5m/min |
Wire feeding speed |
1.5~15m/min 2.2~22m/min |
Rated power source |
500A |
Wire diameters |
Φ1.0/Φ1.2 Φ1.6/Φ2.0 |
Type of wires applicable |
Soft steel, solid core |
Torch rotatable angle |
±90° |
Torch inclination(left and right) |
±45° |
Adjustable distance of torch |
50X60(longitudinal X transversal)does not include primary adjustment |
Axis diameter of wire spool |
φ50 |
Wire spool capacity |
20kg |
Dimension(L×W×H) |
480×480×680 |
Weight |
32kg(does not include wire) |
MR-1000B Plasma Power Source
Main Feature:
▉Adopt IGBT module full-bridge resonant soft-switching inverter technology, which has high efficiency, low no-load consumption and high reliability
▉ Automatic protection from overcurrent, overheating, overvoltage and undervoltage
▉Working current digital display and can be preset in advance
▉ Can output the plasma arc stably, and the arc concentration is high
▉ Strong ability to suppress network voltage fluctuations, with a width of ±20%
▉ Arc ignition mode of power supply: contact arc ignition
Technical Parameter
Model Content |
MR-1000B |
Power source |
3-phase 380V |
Rated input capacity |
114KVA |
Rated input current |
173A |
Rated welding current |
1000A/90V |
Rated duty cycle |
100% |
Adjustment range of welding current |
40A-1000A |
Efficiency |
85% |
No-load voltage |
140-150V |
Weight |
120 Kg |
Air switch |
225A |
Input cable |
3×35 mm2 |
Insulation class |
F |
Raising means |
Lift |
Protection class |
Ip21S |
NBC-500X: Revolutionizing Welding with Intelligence, Efficiency, and Superior Performance
Main features:
■ Digital display and presetting of current and voltage, wide adjustment range of voltage
■ Particular function of automatically removing melting-ball from the end of the welding wire
■ Adopt the double-closed-loop system to control arc, arc burns stably
■ Easy to strike arc, small spatter
■ Wide adjustment range of input voltage: 280V—450V
■ Welding cable can be prolonged to 60m
■ All-digital control, performance is reliable and stable
■ I type machine supports synergic adjustment and presetting of current and voltage
■ When a malfunction occurs, the code automatically displays the cause of the malfunction
Excellent SAW Tractor MZ-ZK
The tractor is developed by absorbing the merits of SAW tractor used both at home and abroad. It features new style, light weight, reliable function and user friendly after our continuous modification and improvement in recent years.
Characteristic:
- The tractor travelssteadily and has a wider welding range for wires fromΦ2.0 toΦ6.0 diameters.
- Easy and flexible regulation. Integrated up and down, rotation of the tractor head with the torch bar.
- Rotatable and height adjustable cross beam
- Easy adjustable flux container.
- Double driven wire feeding with straightening mechanism, stable wire feeding, good centering, strong drawing force and low dissipation power.
NBC-1000P Inverter Hi-speed Automatic Gas-shielded Welding Machine
NBC-1000P is the auto inverter GMAW welding machine Sichuan Morrow Welding Development Co., Ltd. Based on the original NBC series of semi-automatic welder and MZ7 series of auto submerged-arc welding machine. It is specially developed for box beam use. With pulse functions, its molten depth is deeper and welding seam and is more beautiful.
Features
■ IGBT module all-bridge soft-switch inverter technology, high efficiency, energy saving
■ Automatic protection from phase lacking, over-current, over-heat, over/under-voltage
■ Adopt the double-closed-loop system to control arc, arc burns stably
■ Accurate preset of welding current, voltage and march speed
■ Super low-spatter welding to 4mm, 3.2mm SAW wire, and narrow-gap welding
■ Hi-speed pulse big wire welding, high speed,deep molten depth
Technical features
- Using our high-speed pulse gas shielded welding, we don’t need to add bearing block as the general box beam welding, don’t need do bottom welding, and we can also avoid the problem of hardly removing slag in the first or second submerged arc filling welding, thus greatly reducing production costs and further improve the production efficiency.
- For more information, please contact Technical Department of Morrow Welding
|
NBC-1000P |
Power |
3-phase 380V/415V 50Hz |
Rated input power |
59KVA |
Rated input current |
90A |
Rated current/voltage |
800A/44V |
Welding current |
875A 80%DE |
1000A 100%DE |
|
No-load voltage |
90V |
Adjustment range of current |
40-1000A |
Efficiency |
83% |
Factor |
0.95 |
Insulation class |
F |
Protection class |
IP23 |
Standard Configuration
NBC-1000P power source one set
Tractor (with water-cooling head) one set
Control panel one piece
Welding cable 15m
Control cable 15m
Earth cable 2m
Warranty: twelve months for the whole machine, five years for the PCB
Delivery: 30days after receiving your payment if there is no special requirements
Payment term:100% T/T in advance or 100% L/C at sight
Packing: Laminated box with thick foam boat
NBC-800 IGBT Inverter Gas-shielded-Arc Welder
■ Adopt the soft switch technology, high efficiency, low power consumption
■ Automatic protection from over-current, overheat, over/under voltage
■ Support digital display and presetting of current and voltage, wide adjustment range of voltage
■ Particular function of automatically removing melting-ball from the end of the welding wire
■ Adopt the closed-loop system to control arc and waveform control system to adjust the arc force
■ Suitable for low carbon steel and low alloy carbon with solid/flux-cored welding wires of different specifications
■ Widely used in such areas as automobile, shipbuilding, bridge, petrol chemistry and construction, and so on
■ Wire feeder is driven by four wheels, big power, and feeding wire stably
■ A voltage fluctuation of ±20% is allowable
■ Small size, light weight
■ Support frequent welding, little spatter, high efficiency in melting metals
- Main parameters
|
NBC-800 |
Power |
3-phase 380V/415V 50Hz |
Rated input power |
43KVA |
Rated input current |
65A |
Rated current/voltage |
800A/44V |
Welding curr. |
800A 80%DE |
700A 100%DE |
|
No-load voltage |
90V |
Adjustment range of curr. |
40-800A |
Efficiency |
≥85% |
Factor |
0.95 |
Insulation class |
F |
Protection class |
IP23 |
OEM machines can be supplied. We can offer welding machines according to your requirements.
No matter the biggest current is 800A, 1000A, or 1250A, 3000A, or 4000A, we can also offer.
No matter you need 3-phase 380V, 415V, or 220V, we can also offer.
No matter you need blue, yellow, red, grey, black or any other color, we can also offer
No matter what kind of shell you need, we can also offer
Please don't hesitate to contact me if you have any questions or requirement.
Automatic IGBT Inverter Welding Machine
Adopting the most advanced IGBT module, big-scale soft switch IC, and all-bridge inverter loop, our IGBT inverter welder is small in size, light in weight, high efficiency, and low no-load consumption, over 1/3 energy saving compared with the traditional welder. It’s the ideal energy-saving welding equipment.With such features as high respond speed, high performance, beautiful seam, high power input capability, small spatter, low noise, easy to operate and move, it is the ideal equipment. It can support such functions as protection from overheat, overcurrent, and over/under-voltage protection, preset of current and voltage.
1. The main loop adopting the all bridge structure (the structure can support the anti-unbalance well), overcurrent protection and primary overcurrent protection fo transformer, the welding machine is endowed with high reliability;
2. Adopting the soft recovery diode as the rectification part, it is easier to recover, lower temperature;
3. Good procedure design, easy to strike arc, arc burns stably and deep penetration;
4. Strong self-compensation capability, a range of 270V-450V
5.Our company's self-developed and produced DSP series IGBT inverter welding machine is a digital inverter welding machine that can be used for DC CO2, DC MAG, pulse MAG welding of carbon steel, stainless steel, aluminum and other materials. This type of model can support welding of different wires from Φ 0.8- Φ 1.6mms. This machine is equipped with welding expert parameters. Users only need to select the welding material and wire diameter, adjust the wire feeding speed through the wire feeding mechanism, and set the welding voltage or arc length to perform normal welding. Automatic protection from phase loss, overheating, overcurrent, and undervoltage, the machine is an ideal welding equipment with high efficiency and energy conservation
Main Features
■ Input: 270V~450
■ Automatic protection from overcurrent, over/undervoltage, overtemprature, phase-lack
■ Digital display of current and voltage
■ Easy to strike arc and arc burns stably
■ Small, light and low noise
■ Support voltage fluctuation of ±20%
■ Welding tractor is multifunctional, marching speed adjustable, different choice in swinging angle, swinging speed and swinging speed, and the center of swing can be preset
Configuration
The configuration of automatic gas-shielded arc machine are as follows
Name |
Unit Price |
Configuration |
Quantity |
Note |
All-digital MAG welding power source |
|
All-digital MAG welding power source |
1 Set |
Can choose hi-speed pulse welding power source |
MAG welding tractor |
|
MAG welding tractor |
1 Set |
|
Oscillator |
|
Oscillator |
1Set(Optional) |
Angle oscillator or flat oscillator |
Others |
Optional |
Earth cable |
2m |
70mm2 |
Welding cable |
20m |
70mm2 |
||
Control cable |
20m |
7-cored control cable |
||
Gas tube |
20m |
|
||
Gas regulator |
1piece |
|
||
Total |
|
|
|
|
Technical Parameter
- Power source
Model Contents |
NBC-350P |
NBC-500P |
NBC-630P |
|
Input power source |
3-phase 380V 50/60Hz |
|||
Rated input current |
20.7A |
35A |
52A |
|
Rated input capacity |
13.6KVA |
23KVA |
34KVA |
|
Rated welding curr./volt. |
350A/31.5V |
500A/39V |
630A/44V |
|
Rated duty cycle |
60% |
60% |
60% |
|
No-load volt.(MAX) |
72V |
72V |
75V |
|
Adjust. Range of welding curr. |
40-350A |
40-500A |
50-630A |
|
Efficiency |
83% |
83% |
83% |
|
Power factor |
>0.95 |
>0.95 |
>0.95 |
|
Suitable wire |
Φ1.0-Φ1.6mm Solid wire, stainless wire |
|||
Model of wire feeder |
CS-501B |
|||
Weight of wire feeder |
6Kg |
|||
Length of torch cable |
3m |
|||
Cooling means of torch |
Air/Water cooling |
|||
EMC |
A Type |
|||
Weight of machine(kg) |
45 |
55 |
60 |
|
Air switch |
40A |
63A |
63A |
|
Dimension(mm) |
590×306×450 |
640×326×500 |
1110×560×1080 |
|
Input cable(mm2) |
4×6 |
4×10 |
4×10 |
|
Raising method |
Handle |
|||
Insulation class |
F |
|||
Protection class |
IP21S |
|||
External feature |
CV |
2.Welding Tractor
Contents |
Technical Parameter |
Marching speed of tractor |
0~120cm/min |
Swing amplitude |
±0.1º ~ 9.9º |
Swing center position |
At random |
Swing speed |
0.1 ~ 6.0r/min |
Time of left stopping in swinging |
0 ~ 5.0 s |
Time of right stopping t in swinging |
0 ~ 5.0 s |
Time of center stopping in swinging |
0 ~ 5.0 s |
Up-down distance of torch |
10cm |
Left-right distance of swinger |
10cm |
Implementation Standard
- Safety Standard:GB15579-95
- Technical standard:JBIT8748-98
- Welding standard:APT1104
- Insulation Grade:Class F
Documents
- Packing list
- Qualification Certification
- Instruction Manual
- WarrantyCard
RSN-630 inverter stud welding machine for Insulation nails
Features
■ Adopt the soft switch technology, high efficiency, low power consumption
■ Support stud welding and manual welding
■ Automatic protection from overcurrent, overheat, over/under voltage, and phase lacking
■ Strong penetration capability of arc and deeper fusion penetration
■ Easy to strike arc, fine welding seam
■ Stepless adjustment of welding current and welding time
■ Suitable for all kinds of studs
■ A voltage fluctuation of ±20% is allowable
■ Suitable for boiler and pressure container
NBC-500P All-digital Pulse MIG Welder
Features:
- Functions are controlled by a DSP chip and can save 30 sets of parameter
- Automatic switch off in over-current, over/under-voltage, over-heat, phase lacking
- Support fast forward selection on the front panel
- Suport MMA,MIG/MAG and Hi-speed MIG/MAG welding
- Stable pulse welding can be realized with 50A current and Φ1.2mm wire
- Very suitable for mid/thick plate pulse welding with Φ6mm wire
- Can be used with robot to realize automatic welding
- With such functions as primary current/voltage adjustment, 4T current/voltage adjustment, integral/off
selection, saving and reading of welding parameter, spot welding set
- With robot interface and group control interface
- First in China: Hi-speed DC welding
Advantages:
A.In bottom welding, the backside of welding seam is also good, the defects can be avoided
B.Penetration about 20% bigger than the general DC MIG/MAG welding in the big current welding (300A)
C.Welding speed is 15% higher than the general MIG/MAG welding
D.In fillet welding, welding meat is flat and smooth, no bulge
- Iron water flows smoothly and is easy to control in covering welding
- Suitable for sold/flux-cored wire
Comparison of DC MIG/MAG welding and Hi-speed DC MIG/MAG welding
Name |
Protection gas |
Depth |
Back forming in root welding |
Welding speed |
DC MIG/MAG |
CO2 100% or Ar 80% + CO2 20% |
Shallow |
Just so so |
Slow |
Hi-speed DC MIG/MAG welding |
Ar 80% + CO2 20% |
Deep |
Excellent |
Quick |
Comparison of Hi-speed DC pulse welding and one-pulse one-drop welding
Name |
Protection gas |
Arc |
Depth |
Undercut |
Spatter |
Weld speed |
Small current weld |
One-pulse one-drop welding |
Ar 80% + CO2 20% |
Not compressed |
Shallow |
Easy |
Few |
Slow |
Hard |
Hi-speed pulse welding |
Ar 80% + CO2 20% |
Compressed |
Deep |
Not easy |
Few |
Fast |
Easy |
Parameters
Model Contents |
NBC-350P |
NBC-500P |
NBC-630P |
Input power source |
3-phase 380V/415V 50/60Hz |
||
Rated input curr. |
20.7A |
35A |
52A |
Rated input capacity |
13.6KVA |
23KVA |
34KVA |
Rated welding curr./volt. |
350A/31.5V |
500A/39V |
630A/44V |
Rated duty cycle |
60% |
60% |
60% |
No-load volt. (MAX) |
62V |
73V |
84V |
Adjust range of welding curr. |
40-350A |
40-500A |
40-630A |
Curr. adjust. Range in MMA |
20-350A |
20-500A |
20-630A |
Efficiency |
83% |
83% |
83% |
Power factor |
>0.95 |
>0.95 |
>0.95 |
Pre-gas-sending time |
0~10S |
||
Post-gas-sending time |
0~10S |
||
Suitable wire |
Ф0.8~Ф1.6mm solid/flux-cored wire |
||
Air switch |
32A |
63A |
63A |
Insulation class |
F |
||
Protection class |
IP21S |
NBE Series of Inverter AC MIG Welding Machine
Features:
■DSP digital control with 30 storage channels.
■Automatic protection from over-current, over/under-voltage, overheating, and phase loss
■The panel has a function locking key to ensure consistency of welding parameters.
■Water-cooling type and air-cooling optional
■Equipped with all the functions of NBM welding machine, as well as AC pulse/AC dual pulse
■When double pulse welding, the shape is beautiful, the fish scale pattern is clear, the strong and weak pulse conversion is crisp, and the arc sounds clearly.
■Heat input is lower than NBM
■Equipped with robot interfaces.
Parameters of power source
Model Contents |
NBE-350 |
NBE-500 |
NBE-630 |
Input power source |
3-phase 380V 50/60Hz |
||
Rated input curr. |
20.7A |
35A |
52A |
Rated input capacity |
13.6KVA |
23KVA |
34.2KVA |
Rated welding curr./Volt. |
350A/31.5V |
500A/39V |
630A/44V |
Rated duty cycle |
100% |
100% |
100% |
No-load voltage (MAX) |
63V |
77V |
82V |
Adjust range of welding curr. |
40-350A |
40-500A |
50-630A |
Efficiency |
85% |
85% |
85% |
Power factor |
>0.95 |
>0.95 |
>0.95 |
Suitable wire |
Φ1.0-Φ1.6mm Al, AlSi, AlMg wire |
||
Model of wire feeder |
CS-501B |
||
Weight of wire feeder |
16Kg |
||
Length of torch cable |
3m |
||
Cooling means of torch |
Water cooling |
||
EMC |
type |
||
Air switch |
40A |
63A |
63A |
Insulation class |
F |
||
Protection class |
IP23S |
Parameter of wire feeder
Rated voltage |
34V |
Rated current |
3A |
Feeding speed |
1.5-25m/min |
Reel shift diameter |
50mm |
Reel width |
103mm |
Wire weight |
25Kg |
Weight |
16Kg |
Dimension |
640×250×400 |
Wire diameter |
0.8-1.5mm |
Wire |
Solid, flux-cored, soft |
Questions and Answers
1. Questions: Are you a factory or trading company?
ANSWER: We are welding machine manufacturer with more than 30 years of history. We have our own plant and land and all products are strictly produced with ISO9001:2013, and equipment, so we can meet both your quantity and quality demands.
2. Questions: how about your MOQ:
ANSWER: Generally if you choose the different products, our minimum order qty. also will be different.
3. QuestionsPayment means:
ANSWER: Actually, payment would be preferred: Normally we choose in T/T and LC
4. Questions: When can I get the products?
ANSWER: Your products will arrive your the nearest domestic port after the order is confirmed, it's about 30 days.
Field Charging MMA/TIG Welding Machine--YW-3500T
YW-3500T, the weld-chargeable MMA/TIG welding machine, a revolutionary welding solution that combines cutting-edge technology with environmental sustainability.
This innovative welder is equipped with a 48V lithium iron phosphate battery to provide reliable, efficient power for all your welding needs. When fully charged, the welder can run for up to 4 hours, allowing you to complete your welding tasks without constant charging.
Field-chargeable MMA/TIG welding machines are designed to support MMA and TIG welding processes, providing versatility and flexibility for a variety of welding applications. Whether you work in metal fabrication, construction, or automotive repair, this welder is the perfect companion for professional welders and DIY enthusiasts alike.
One of the main features of this welder is its environmental friendliness and low cost of operation. By using lithium iron phosphate batteries, the welder reduces reliance on traditional fuel-fired generators, minimizing carbon emissions and promoting a cleaner, greener working environment. Additionally, lower operating costs make it an economical choice for businesses and individuals looking to reduce their welding expenses without compromising performance.
As a welder generator, the field-chargeable MMA/TIG welder offers the convenience of a portable power source with the functionality of a high-quality welder. Whether you're working in a remote location or on-site on a construction project, this welder provides the power and performance you need to get the job done efficiently. Its compact and portable design makes it easy to transport and install, ensuring you have reliable welding capabilities wherever you work.
As a leading welding machine supplier, we pride ourselves on delivering top-notch welding solutions that meet our customers' needs. Field-chargeable MMA/TIG welding machines demonstrate our commitment to providing innovative and sustainable welding equipment that results in superior welding results. With advanced battery technology and versatile welding capabilities, this welder is a game changer for professionals in the welding industry.
In addition to its welding capabilities, field-chargeable MMA/TIG welders can also act as generators to provide auxiliary power for tools and equipment on the job site. This dual functionality makes it a valuable asset for a variety of applications, allowing you to maximize productivity and efficiency without having to use multiple devices.
Whether you need an arc welder, a generator, or a welding generator, a field-chargeable MMA/TIG welder is an all-in-one solution for your welding and power generation needs. Its reliable performance, environmentally friendly design and cost-effective operation make it an excellent choice for professionals and amateurs who require the best in welding technology.
In summary, the field-chargeable MMA/TIG welder is a game-changing welding solution that combines the power of a welder generator with the efficiency of a sustainable power source. With advanced battery technology, versatile welding capabilities and dual functionality as a generator, this welder sets new standards in performance, convenience and environmental responsibility. As a leading welding machine supplier, we are proud to offer our customers this innovative welding machine, providing them with a reliable and sustainable solution for all their welding needs.
Digital Inverter Tri-wire Tri-arc SAW Welding Machine
Our Tri-wire tri-arc SAW machine is developed based on the all-digital submerged arc welding machine.
One system include one MZ7-1600 DC submerged-arc power source and two sets of MZE-1250 AC/DC square-wave submerged-arc power sources,and one three-wire welding tractor as well as one control panel.
Features:
▉ Both power source and tractor DSP all-digital control and digital communication
▉ With expert database, and 30 saving channels
▉ Digital display and presetting of current, voltage and marching speed
▉ AC frequency, duty ratio adjustable
▉ AC/DC power source and DC power source work simultaneously without affecting each other
Technical Features:
- DC power source goes ahead, and AC/DC power source flows, which guarantee good appearance and good weld
- In welding, the given welding parameters of DC power source should be bigger than or equal tothat ofAC/DC power source
- After grating feedback control, wire feeding will be more stable and can speed up before resistance, especially suitable for barrel wire
- With auto warning function after wire touches the workpieces well, high arc-ignition success rate
- Duty ratio of 50% and frequency of 15-30 is recommended
- Suitable for high-speed high-efficiency welding of thick plate and ultra-thick plate
- Especially suitable for using in petrol tube, gas tube, ship making, wind tower, and son on
Technical parameter of DC power source
|
MZ7-2000 |
Input power |
3-phase 380V /415V 50Hz |
Rated input power |
114KVA |
Rated input current |
172A |
Welding curr. |
2000A 80%DE |
1550A100%DE |
|
No-load voltage |
92V |
Welding curr. |
100-2000A |
Diameter of wire |
4-6mm |
Wire feeding speed |
50-460cm/min |
Welding speed |
0-120cm/min |
Capacity of flux container |
10L |
Capacity of wire container |
20Kg |
Weight of tractor |
45Kg |
Air switch |
225A |
Input cable |
3 x 16mm2 |
Insulation grade |
F |
Raising means |
Lift |
Protection grade |
IP21S |
Parameter of AC power source
Model Contents |
MZE-1250 |
Input power source |
3-phase 380V 50/60HZ |
Rated input power |
71KVA |
Rated input curr. |
108A |
Weld curr. |
1250A 60% |
1000A 100% |
|
No-load voltage |
82V |
Adjust range of welding curr. |
200-1250A |
Suitable wire |
Φ3-6mm |
AC frequency |
5~100Hz |
Duty ratio |
0~100% |
Air switch |
160A |
Input cable |
4×16 mm2 |
Insulation class |
F |
Protection class |
IP21S |
Inverter Single-arc Double-wire SAW Welding Machine (big wire)
Features:
▉ IGBT module full-bridge soft switching inverter technology, high efficiency, energy saving
▉ Automatic protection from phase loss, over-current, overheating, over-voltage and under-voltage
▉ Precise preset welding current, voltage and march speed
▉ Wide voltage adoption, with a voltage fluctuation of ±20%; 100% duty cycle
▉ Wire feeding auto detecting, when it is in good contact with the workpiece, wire feeding will stop aromatically, press and hold to automatically accelerate the feeding and unwinding, and automatically unwind the wire after welding.
▉ Can realize efficient welding of thick plates instead of tandem wire tandem-arc SAW machine
▉ Two kinds of heads:: A (diameter of forward wire is 3.2mm, and that of backward wire is 4mm or 5mm)
B: (the diameter of two wires is the same)
▉ Double wires do not affect each other, do not interfere with each other, and have strong arc penetration
▉ It can realize high-effective welding to thick plate instead of double-wire double-arc welding and high-efficiency
surfacing in double-wire parallel welding
▉ It is the first choice welding power source for gantry welding, welding manipulators and other special
Technical Features:
①Thick wire ahead thin-wire-following big penetration welding
- The front wire starts arc while touching the workpiece and the rear wire doesn’t need to touch workpiecs
for arc starting
- Diameter of front wire is 3.2mm, the diameter of rear wire is 4mm, and the welding currents will be matched
Automatically according to the proportion of 2:1
- The distance between two wires is 3-6mm, the front wire can increase the molten depth, and the rear can increase the molten width
- There is no need to bevel and leave a gap when welding on both sides of the T type weld with a plate thickness of 30mm
②The same thick wire welding
- The front wire starts arc while touching the workpiece and the rear wire doesn’t need to touch workpieces for arc starting
- The welding current of front and rear wires is automatically matched by 1:1
- The distance between the front and rear wires is 3-6mm, the front wire increases the penetration depth, and the rear wire increases the molten width
- It can replace double wire double arc submerged arc welding
③Efficient surfacing of the same thick wire (for surfacing, a special surfacing control box is required)
- Two welding wires of the same thickness are welded in parallel
- The left and right wire welding current is automatically matched according to 1:1
- The width of one-time welding weld can reach more than 40mm
Model Contents |
MZ7-2000 |
MZ7-2500 |
Input power source |
3-phase 380V 50/60Hz |
|
Rated input power |
114KVA |
142KVA |
Rated input curr. |
172A |
215A |
Adjust range of welding curr. |
200-2000A |
200-2500A |
Air switch |
225A |
250A |
Rated duty cycle |
100% |
|
No-load voltage |
92V |
|
Efficiency |
85% |
|
Wire-feeding speed |
50-460cm/min |
|
Welding speed |
0-120cm/min |
|
Capacity of flux container |
10L |
|
Capacity of wire spool |
20Kg |
|
Weight of tractor |
45Kg |
|
Insulation class |
F |
|
Protection class |
IP23S |
|
Input cable |
3 × 16 mm2 |
3 × 25 mm2 |
MZ7 Series of Inverter Hot-wire SAW Welding Machine
Features:
▉ IGBT module, all-bridge soft-switch inverter technology, high efficiency and power saving
▉ Automatic protection from phase lacking, over current, over-heat, over/under voltage
▉ Precise presetting of welding current, voltage and marching speed
▉ CC/CV, suitable for both thin and thick wires
▉ Support SAW, MMA, and gouging
▉ Excellent touchable arc starting and no-touching arc starting function
▉ Strong arc penetration force, different welding tractors are optional
▉ Wire feeding auto checking, while the wire connects the work-pieces well, wire-feeding stops automatically, press the wire sending/back without release, wire sending or wire feeding will be speed up automatically, wire will be drawn back automatically after welding finish
▉ Wide voltage adoption, ±20%
▉ Can weld mild steel and stainless steel, the first-choice power source of gantry welding and operator.
▉ In hot wire welding, the welding wire is preheated to 500-900℃ in advance before being fed into the arc area, therefore, the molten speed of unit current wire is increased, and the welding efficiency is increased accordingly
▉ In hot wire welding, under the same current conditions, the welding wire melting speed can be increased by about 15-30%; the heat input of the weld is reduced by 10-20%; the penetration depth is increased by 10-20%; the flux consumption is reduced by 10-30%
Parameters
Model Name |
MZ7-1000 |
MZ7-1250 |
MZ7-1600 |
Power |
3-phase 380V 50/60Hz |
||
Rated input power |
59KVA |
73KVA |
93.9KVA |
Rated input current |
90A |
111A |
143A |
No-load voltage |
90V |
92V |
92V |
Adjustment range of current |
40-1000A |
60-1250A |
80-1600A |
Efficiency |
85% |
||
Rated duty cycle |
100% |
||
Air switch |
100A |
125A |
160A |
Wire-feeding speed |
50-460cm/min |
||
Weld speed |
0-120cm/min |
||
Capacity of flux container |
10L |
||
Capacity of wire spool |
20Kg |
||
Weight of tractor |
45Kg |
||
Input cable |
3 × 16 mm2 |
3 × 16 mm2 |
3 × 16 mm2 |
Insulation grade |
F |
||
Protection class |
IP23S |
Suitable industries:
Construction machinery, pressure vessels, shipbuilding, steel structures, wind towers, metallurgy, petroleum, bridges, etc.
Automatic SAW-630 for Thin Sheet Welding
Congratulations on using IGBT series of submerged arc welder!
IGBT series of inverter submerged arc welder is a kind of new-type completely automatic welder our company developed and manufactured according to our nationalities after absorbing advanced technologies of similar products. It has reached the international level on both main technical indexes and welding performance, and lies in the leading position in China.
Adopting the latest big-power IGBT switch parts, and using the small and light HF transformer to replace the heavy power frequency transformer of the traditional welder, IGBT series of submerged arc welding generator is endowed with such features as high efficiency, small no-load consumption, welding current stable, energy saving, and material saving, etc. The welding tractor, output of the modern high technology, adopts the advanced electronic switch to control the cut and connection of power source, thus it is small in size, light in weight, easy to adjust and use, rather stable and high reliable, etc. It is especially suitable for the quick welding of metal parts of middle/thick thickness such as pressure vessel, machinery processing, steel structure, and ship building, etc.
MZ7-630 |
MZ7-800 |
|
Input power |
3-phase 380V 50Hz |
|
Rated input power |
34KVA |
45KVA |
Rated input current |
52A |
68.5A |
Welding curr. |
630A 60%DE |
800A 60%DE |
500A 100%DE |
630A 100%DE |
|
No-load voltage |
70-80V |
70-80V |
Welding curr. |
200-630A |
200-800A |
Diameter of wire |
Φ2-3.2mm |
Φ2-4mm |
Weight of welder |
62Kg |
70Kg |
Wire feeding speed |
50-460cm/min |
|
Welding speed |
0-120cm/min |
|
Capacity of flux container |
10L |
|
Capacity of wire container |
20Kg |
|
Weight of tractor |
45Kg |
|
Air switch |
63A |
63A |
Insulation grade |
F |
|
Raising means |
Lift |
|
Protection grade |
IP21S |
- Marching speed meter: show the marching speed
- Marching speed knob of tractor: while being rotated clockwise, the marching speed will become higher, or it will become lower
- Wire-feeding button: touch the button, the wire will be feed slowly; if thebutton is pressed for about 3 seconds, the wire feeding will speed up.
- Wire back button: touch the button, the wire will be withdrawngradually. If the button is pressed for about 3 seconds, the wire withdrawing speed will speed up.
- Voltmeter: show the actual output voltage
- Welding voltage knob: adjust it clockwise while doing welding, the voltage will become higher, or it will be lower
- Backward/Forward switch: on the position of “Forward”, the tractor will go ahead; if on the position of “Backward”, the tractor will go back
- CV/CC switch: on the position of CV, the tractor is in constant current; on the position of CC, the tractor is in constant voltage
- March button: the tractor will move if thebutton is pressed
- Ammeter: show the actual output current
- Welding current knob: while doing welding, adjust it clockwise, the welding current will increase, or it will decrease
- Welding button: touch the button while needing doing welding, the tractor will begin to move and the welding will begin.
- Stop button: touch the button, the tractor will stop moving and thewelding will also stop
Package
Digital AC/DC Square-wave SAW Welding Machine
Our all-digital AC/DC square-wave SAW machine is developed on the DC SAW machine adopting the inverter technology twice, with wonderful welding result. The details is: the 3-phase 380V/50Hz power will change into HF AC after the filtration of the power frequency rectifier and role of inverter. And over high-frequency transformation and rectification, feedback control of output signal, the smooth and continuously adjustable DC will be got. After the second inversion, the DC will be changed into low-frequency AC for automatic welding of work pieces.
Features
▉ Both power source and tractor DSP all-digital control and digital communication
▉ With expert database, and 30 saving channels
▉Menu and functions LCD display and control, easy to operate
▉ Start-arc anti-stick, auto wire back while arc stops
▉ Digital display and presetting of current, voltage and marching speed
▉ Support MMA, SAW and gouging
▉ AC frequency and duty ratio adjustable
Technical Features
- CC and CV in both DC welding and AC welding
- AC CV is recommended for AC quick welding, arc can burns more stably
- With auto alarmfunction after wire touches the workpieces well, high arc-ignition success rate
- 4. Duty ratio of 50% and frequency of20-35Hz is recommended
Parameters
Model Contents |
MZE-1000D |
MZE-1250D |
Input power source |
3-phase 380V 50/60HZ |
|
Rated input power |
56.6KVA |
71KVA |
Rated input curr. |
86A |
108A |
No-load voltage |
82V |
82V |
Adjust range of welding curr. |
200-1000A |
200-1250A |
Duty cycle |
100% |
100% |
Suitable wire |
Φ3-5mm |
Φ3-6mm |
AC frequency |
5~100Hz |
|
Duty ratio |
0~100% |
|
Air switch |
100A |
160A |
Input cable |
3×16 mm2 |
3×16 mm2 |
Insulation class |
F |
|
Protection class |
IP23S |
Parameter of DC power source
Rated input voltage of travelling mechanism |
Servo motorDC110V (permanent magnet) |
Rotation angle of cross beam |
±90° |
Rated input voltage of wire feeding mechanism |
Servo motorDC110V(Permanent magnet or electric excitation for optional) |
Rotation angle of the tractor head |
45° |
Welding speed range |
0.2-1.5m/min |
Torch inclination |
45° |
Wire feed speed range |
0.25-2.5m/min |
Flux container volume |
6L×2 |
Wire diameter |
2.0/3.0 3.0/4.0 4.0/5.0、6.0 |
Wire spool capacity |
2×25kg |
Adjustable height of crossbeam |
100mm |
Overall dimension |
1100 ×900 × 770 |
Two head can adjust the distance |
600 mm |
Weight |
71kg |
TIP TIG Welding System
I. Configuration
Welding power source 1pc
Hot-wire power source 1pc
Water-cooling system 1pc
Vibration digital wire feeder 1pc
II. Main Parameter
Welding power source:
Welding current: 20-400A
Current type: DC/Pulse
Hot-wire power source:
Hot-wire current: 10-200A
Current type: DC/Pulse
Wire feeder:
Servo wire feeding motor, wire feeding speed: 0-10 m / min,
Mechanical vibration wire feeding, vibration frequency 0-50Hz
Touch screen operator panel:
10″ touch screen operation;
Parameter setting, display, uploading;
Industrial computer operation panel:
10″ industrial computer touch screen operation;
Parameter setting, display, storage, upload.
III. Main Features and Performance
I) Functions of Vabrication wire-feeding
- Stir the molten pool and make the crystal grains more fine, and the mechanical properties of the weld better;
- Stirring to remove volatile gases and bubbles in the molten pool, improving the quality of welding;
- The function of vibration improves the all-position welding ability;
- The function of vibration makes the droplets easily escape from the welding wire into the molten pool.
II). Functions of automatic wire feeding function
- Constant filling function with optimal direction and angle
- The length of the welding wire entering the molten pool is always the same, and the welding quality is consistent.
- Constant and sustainable wire feeding improves wire feeding efficiency and reduces the number of arcing stops.
III) Hot wire function:
- reduce the welding current;
- Improve the efficiency, the current automatic welding test welding speed reaches 720mm / min.
IV) Industrial computer control technology
- The panel function is intuitive and easy to understand, and the operation is convenient, and the interface can be customized at will;
- Data setting and reading all implement bus control mode, and digital communication is more accurate;
- Welding process: full recording of parameter data such as welding current, welding voltage, wire feeding speed, vibration frequency and hot wire current;
- Data upload via wireless and limited network; convenient access to MES system,company server or cloud.
(Industrial computer interface )
(Touch screen interface)
WS7-400-B IGBT Inverter DC TIG Welding Machine for cellulose electrode
WS7-400-B IGBT Inverter DC TIG Welding Machine for cellulose electrode
Discover the next level in welding technology with our high-frequency argon arc welding machine! Engineered with cutting-edge IGBT inverter technology, this machine sets a new standard in efficiency and performance. Whether you're a professional welder or an enthusiast, our welding machine ensures stable arcs and remarkable energy savings, making it ideal for various applications, including the precise handling of cellulose electrodes.
### Unveil the Power of IGBT Inverter Technology
At the heart of our welding machine lies IGBT inverter technology. This advanced feature guarantees superior performance and efficiency compared to traditional welding machines. By leveraging IGBT modules, our equipment achieves seamless power conversion, resulting in reduced energy consumption and increased welding precision. Whether you're working on stainless steel, aluminum, or carbon steel, expect consistent and reliable welding arcs that meet the highest industry standards.
### Efficiency Redefined: High Performance, Low Energy Consumption
Say goodbye to inefficiencies with our high-frequency argon arc welder. Thanks to its IGBT inverter, it optimizes power usage, ensuring that more energy is directed to the welding process and less is wasted as heat or in electrical losses. This not only saves you money on electricity bills but also enhances productivity by maintaining stable welding conditions throughout your work.
### Perfect Companion for Cellulose Electrodes
Designed with versatility in mind, our welding machine excels with cellulose electrodes. Its precise control over arc stability and current flow ensures clean welds with minimal spatter, even when handling challenging materials. Whether you're in construction, automotive repair, or metal fabrication, our machine's ability to handle cellulose electrodes with ease makes it a standout choice.
### Built to Endure: High Duty Cycle and Durability
Expect uninterrupted welding sessions with our machine's high-duty cycle capability. Its robust construction and efficient cooling system allow it to sustain long hours of operation without overheating or performance degradation. This reliability ensures that you can tackle large projects or demanding tasks with confidence, knowing that your equipment won't let you down.
### Why Choose Our High-Frequency Argon Arc Welding Machine?
- **Advanced IGBT Inverter Technology:** Ensures superior welding performance and energy efficiency.
- **Stable Arcs:** Provides consistent arc stability for high-quality welds.
- **Ideal for Cellulose Electrodes:** Handles cellulose electrodes effortlessly, minimizing splatter.
- **High Duty Cycle:** Designed for continuous and reliable operation.
- **Energy Efficient:** Reduces power consumption without compromising performance.
Discover the future of welding technology with our high-frequency argon arc welding machine. Whether you're upgrading your workshop or starting a new project, our equipment promises unmatched performance and reliability. Explore the possibilities and elevate your welding experience today!
Model Content |
WS7-400-B |
|
Power |
3-phase 380V 50Hz |
|
Rated Input capacity (KVA) |
17 |
|
Rated input current (A) |
26 |
|
Rated welding current (A) |
400 |
|
Duty cycle |
100% |
|
djust. Range of welding curr. |
20-400A |
|
Efficiency |
85% |
|
O.C.V. |
TIG |
40-50V |
MMA |
70-80V |
|
Up/down-slope time of welding curr. |
0-10S |
|
Pre-gas sending time |
1S |
|
Post-gas sending time |
5S |
|
Insulation class |
F |
|
Weight(Kg) |
35 |
|
Dimensions(mm) |
590×306×500 |
WSE Series of IGBT Inverter AC/DC Square-wave TIG Welding Machine (All-digital)
Features:
■ Soft-switch inverter technology, all-digital DSP control, world-advanced level
■ With welding expert database inside, can save 30 sets of self-set parameter
■ Automatic protection from over-current, over/under-voltage, over-temperature
■ All-digital LCD menu to show all functions and data, easy to operate
■ Can get ideal rectangular wave AC/DC no matter the current is small or big
■ Cleaning ratio and cleaning width continuously adjustable, the adjustment range is wide
■ Support TIG spot welding, DC MMA welding, DC TIG welding, DC pulse TIG welding, square-wave TIG welding
■ Support adjustment of initial current, up-slope of current, down slope of current, collector current, to realize high-quality welding
■ Wide usage, support high-quality welding of all kinds of metals and alloys
MZ7 Series of Inverter Automatic SAW Welding Machine (DSP All-digital Control)
Features:
■ IGBT module as the main power apparatus, adopt soft-switch inverter technology, high efficiency, power saving
■ DSP all-digital control and communication of machine and tractor
■ With expert database inside, can keep 30 sets of parameter
■ All-digital LCD menu to show function and parameter
■ Anti-stick, automatic arc filling, automatic wire back-sending while arc stopped
■ Wide adjustment range of welding voltage, small fluctuation of welding current and voltage
■ Digital display of current, voltage, and marching speed
■ Support GTAW and carbon gouging, high using ratio
■ Input voltage fluctuation of ±20% is tolerable
MZE Series of Tandem SAW Welding Machine
Features:
■ Both power source and tractor DSP all-digital control and digital communication
■ With expert database, and 30 saving channels
■ Menu and functions LCD display and control, easy to operate
■ Start-arc anti-stick, auto wire back while arc stops
■ Digital display and presetting of current, voltage and marching speed
■ AC frequency and duty ratio adjustable
■ AC/DC power source and DC power source work simultaneously without affecting each other
ND Series of Inverter MMA/TIG/MAG Welding Machine
Feature
■ Soft switch technology, DSP all digital control
■ With expert database, can keep 30sets of parameters
■ Automatic protection from over-current, overheat, over/under-voltage
■ Arc burns stably, strong penetration force, big molten pool
■ Support cellulose/low-hydro electrode GTAW welding, TIG welding, flux-cored wire self-protection welding, GMAW
DSP All-digital Hi-speed Pulse Inverter Welding Machine
Features:
■DSP all-digital control, with 30 saving channels
■Automatic protection from over-current, over/under-voltage, over-heat, phase lacking
■With function lock-key on the front panel, can guarantee the consistency of welding parameters
■Support hi-speed pulse welding, hi-speed double-pulse welding, vertical upward welding, root welding and cold-arc welding
■Can weld stainless steel, high strength steel, high alloy steel, low alloy steel, carbon steel, various nickel (iron, cobalt) based alloys well
■With robotic interface and group control interface
Pulse MIG Welding Machine for Carbon Steel and Mild Steel
Features
Our company developed the second generation high-speed pulse MIG welding machine on the basis of the first generation normal pulse MIG welding machine, it solved the process of pulse MIG welding thickness, medium and thin carbon steel plate, and further enhances the process of welding aluminum and its alloys and stainless steel.
1.Almost no spatter.
2.High-speed pulse makes large current to automatically form compression arc, a greater depth of molten, groove can be changed from 60° to 30° or 40°, thus greatly improve production efficiency and reduce cost.
3.Small current has cold arc welding process, φ1.2 aluminum wire uses 30A, φ1.2 carbon steel wire uses 35A, φ1.2 stainless steel welding wire uses 35A, which makes the arc more stable.
4.High speed pulse MIG background welding can replace TIG welding, and the velocity is 4-5 times of argon arc welding, and the front and back forming are comparable with argon arc welding.
DSP Digital Hi-speed Pulse Inverter Welding Machine
Features:
■DSP all-digital control, with 30 saving channels
■Automatic protection from over-current, over/under-voltage, over-heat, phase lacking
■With function lock key on the front panel, can guarantee the consistency of welding parameters
■Grating feedback wire feeding unit is used in wire feeder, digital display and setting of welding current and voltage on the front panel of wire feeder, digital communication with power source
■Besides the functions of DSP (TG3), can weld aluminum and its alloys, galvanized sheet, brass, copper and other metals well
■With robot interface and group control interface
NBM Digital Inverter Double-Pulse MIG Welding Machine
Features:
■ Specially for aluminum and its alloy, can realize perfect weld of aluminum, aluminum silicon, aluminum magnesium
■ DSP digital control, with 30 saving channels
■ Automatic protection from over-current, over/under voltage, overheat, phase lacking
■ With function lock key on the front panel, can guarantee the consistency of welding parameters
■ Water-cooling type or air-cooling type optional
■ Support single-pulse welding, double-pulse welding, DC welding, spot welding, setting of primary current/current, 4T current/voltage adjustment, synergic/off selection, saving and read of welding parameters
■ In double-pulse welding, weld beautiful, ripple clear, strong and weak pulses converter quickly, arc sounds clearly
■ With robotic interface, can be used with robots
NBC(P) All-Digital Inverter Gas-Shielded Welding Machine
■DSP all-digital control, with 30 saving channels
■Automatic protection from over-current, over/under-voltage, over-heat, phase lacking
■With fast forward key on the front panel
■Suport MMA, MIG/MAG and Hi-speed MIG/MAG welding
■Stable pulse welding can be realized with 50A current and Φ1.2mm wire
■Very suitable for mid/thick plate pulse welding with Φ1.6mm wire
ZX7 Series of Inverter Carbon Arc Gouging Machine
Features:
▉ IGBT module all-bridge soft-switch inverter technology, high efficiency, energy saving
▉ Automatic protection from phase lacking, over-current, over-heat, over/under-voltage
▉ Industrial use, 100% duty cycle
▉ Support gouging and stick welding
▉ Gouging seam deep and smooth
▉ Can work well even the grid voltage is around +/-20%
RSN7 Series IGBT Inverter Stud Welder
Features
■ Adopt the soft switch technology, high efficiency, low power consumption
■ Support stud welding and manual welding
■ Strong penetration capability of arc and deeper fusion penetration
■ Easy to strike arc, fine welding seam
■ Stepless adjustment of welding current and welding time
■ Suitable for welding all kinds of studs and bolts
MZ7 Series of IGBT Inverter Submerged Welding Machine
Features
★ Soft switch technology, high efficiency, energy saving
★ Automatic switch off while the machine is in over current, overheat, over/under-voltage
★ Multifunctional: SAW, MMA, Gouging
★ Small, light, and easy to operate
★ CC/CV, can weld thin wire like 1.6-2.4mm as well as the general wire of 3-5mm
★ Can be used with column and boom
WSE Series IGBT Inverter AC/DC Square-wave Welder
Features
■ Automatic protection from over-current, overheat, over/under voltage
■ Support AC/DC square-wave TIG welding, DC TIG welding, MMA welding
■ Small size, light weight, high shift efficiency, energy saving, strong adaptability of the voltage
■ In TIG welding, the up/down slope of welding current can be adjustable, and with the function of pre-gas sending and delay gas sending
■ HF automatically strike arc, and extinguishes automatically after the arc is successfully started
■ In MMA welding, can be used together with almost all kinds of welding electrode with a diameter below 5.0mm
■ While DC TIG welding is adopted, can weld all kinds of stainless steel parts, pressure container and pipeline
■ While AC square-wave welding is adopted, can weld the nonferrous metals like aluminum and aluminum alloy, and so on.
■ Adopt inverter technology twice, pure square-wave output, heat concentrated, strong reverse clearance capability; cleaning frequency and ratio can be adjusted, can easily adjust the result of deoxidation in aluminum welding. The mixing ratio and frequency is preset, can effectively protect the tungsten electrode and prolong its service life.
■ Can be equipped with the distance control box to realize the distance control, simplify the operation.
WSM7 Series of IGBT Inverter Pulse TIG Welding Products
Features
■ Adopt the soft switch technology, high efficiency, low power consumption
■ Automatic protection from overcurrent, overheat, over/under voltage
■ Support DC TIG welding, pulse TIG welding and MMA welding, can weld such metals as stainless steel, alloy steel, copper, silver, titanium, etc.
■ In TIG welding, can select DC or pulse welding according to the requirements, can adjust the peak/bottom current, pulse duty circle and frequency according to the size of welding seam
■ In TIG welding, HF automatically strikes arc, and extinguish automatically after the arc is successfully stroke, high efficiency
■ With the long/short seam switch and gas/water cooling switch, can make selection according to the actual need
■ In MMA welding, suitable for the electrode with a diameter of below 5.8mm
■ Can realize TIG grounding and MMA covering once a time, high efficiency, especially suitable for the welding of thin rare-metal board
■ Wide range of supply voltage, as wide as ±20%
WS7 Series of IGBT Inverter DC TIG Welder
Features
■ Adopt the soft switch technology, high efficiency, low power consumption
■ Automatic protection from overcurrent, overheat, over/under voltage
■ Support TIG welding and MMA welding
■ Up/down-slope of welding current continuously adjustable, pre-gas sending and delay gas sending
■ HF automatically strikes arc, and automatically extinguishes after the arc is successfully stroke
■ In TIG welding, the long/short seam switch can support the switch between continuous welding and discontinuous welding. The build-in circuit guarantees a good arc-ignition and crater filling, and endows the machine with such features as easy to start arc, arc heat concentrated, good gas protection result, etc.
■ In MMA welding, can be used together with all kinds of electrode with a diameter below 0.5mm. In TIG welding, can weld stainless steel, alloy steel, copper, silver, titanium
■ With arc-striking current adjustment switch, can easily adjust the arc-striking current, optimize the arc ignition effect. The pushing current adjustment knob can strengthen the arc force and prevent the welding electrode stuck to workpieces
■ Can be equipped with the distance control box to realize distance control, simplify the operation
■ Can be used in welding the stainless steel parts, pressure container and pipeline, realize TIG grounding and TIG covering once a time, greatly improve the working efficiency
ZX7 Series IGBT Inverter DC MMA/TIG Welder
Features:
■ Adopt the soft switch technology, high efficiency, low power consumption
■ Automatic protection from overcurrent, overheat, over/under voltage
■ Arc burns stably, quiet molten pool, fine welding seam
■ Touchable arc ignition in TIG welding
■ Support digital display of current and voltage, and presetting of current
■ Small size, light weight, easy to move and operate
■ With arc-ignition current adjustment switch, can easily adjust the arc-ignition current and optimize the arc-ignition effect. With pushing current adjustment switch, can strengthen the arc force and prevent the welding electrode stuck to workpieces
■ Can be used together with all kinds of welding electrode with a diameter of within Ф5.0mm in almost all areas
■ Can be equipped with distance-control box according to the requirements of customers, simplify the operation
■ Wide range of supply voltage, as wide as ±20%
NB-K Series of Integral Portable CO2 Welder
Features
■ Protection from phase lacking, overheat, overcurrent, over/under voltage
■ Digital display and preset of current and voltage, wide adjustment range of voltage
■ The special automatic molten-ball moving function at the end of wire
■ Adopt the double-close-loop system to control the arc and wave control system to adjust the arc force
■ Strong self-adjustability of arc, weld stably
■ High transition efficiency, small spatter, high molten rate of metal
■ Small distortion, fine welding seam
■ Easy to start arc
■ Smart, light, and easy to operate
■ SMAW welding supported
NB Series of Portable CO2 Welder
Features
■ Adopt the soft switch technology, high efficiency, low power consumption
■ Strong self-adjustability of arc, weld stably
■ Support frequent welding, little spatter, high efficiency in melting metals
■ Small distortion, fine welding seam
■ Auto protection from phase lacking, over-temperature, over-current, over/under voltage
■ Can weld the thin-board framework made of low carbon steel and low alloy under the help of the solid-cored wire with a diameter of Φ0.8, Φ1.0mm
■ Using area: automobile manufacturing, small-size workpieces processing, upholstering, and maintenance, etc.
■ Support the voltage fluctuation of ±20%
■ Support MMA/MAG welding
NBC Series of IGBT Inverter MIG/MAG Welding Machine
Main features:
■ Support digital display and presetting of current and voltage, wide adjustment range of voltage
■ Particular function of automatically removing melting-ball from the end of the welding wire
■ Adopt the double-closed-loop system to control arc, arc burns stably
■ Easy to strike arc, small spatter
■ Wide adjustment range of input voltage: 280V—450V
■ Welding cable can be prolonged to 60m
■ DSP control technology is adopted in the all-digital machines, performance is reliable and stable
■ I type machine supports synergic adjustment and presetting of current and voltage
Introduction to MZ7 Series of SAW Welder
Features:
★ Soft switch technology, high efficiency, energy saving
★ Automatic protection from over current, overheat, over/under-voltage
★ Multifunctional: SAW, MMA, Gouging
★ Small, light, and easy to operate
★ CC/CV, can weld thin wire like 1.6-2.4mm as well as the general wire
★ Can be used with column and boom
★ Usage: boiler, pressure container, shipbuilding, steel structure and petrochemicals, and so on.